• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair an Ignition Lock Cylinder

If your car's key will not turn or turn, it's time to replace the cylinder that controls the ignition. The lock cylinder is a tumbler made of mechanical that your key can slide into, in contrast to the switch, which is an electrical part of the ignition system.

Over time, "wafers" can break or become worn out. The use of WD-40 or graphite may temporarily resolve the issue however replacement is the only solution that lasts.

Eliminating the Steering Column

Modern cars do not use steering column locks. Instead, they use a key that is used to start the car by pressing and turning the switch on the dashboard panel. This newer system works much more efficiently and is less complicated than the older lock-cylinder method. Some older cars still use the traditional lock cylinder. If this part fails, it could be necessary to replace it to allow the car to start. This is not a job for the novice and should be left to professionals.

Remove the trim panels that cover the upper and lower column of the steering with a screwdriver. This will allow you access to the area around your steering column.

You will see an Allen head bolt on the side of the steering wheel closest to the driver. This bolt holds the unit for the wiper/signal unit in place. Unscrew this bolt and set it aside. Depending on your car's year, you may find three or four small screws with flat heads that keep the plastic over the turn-signal switch in place. Unscrew them and put them aside.

To get to the lock cylinder, you will have to take off the signal/wiper assembly. This requires the use of a specific tool or you can ghetto do it with an object of metal such as a cold chisel. A locksmith can also use an instrument to remove bolts.

If you are unable to insert the key into the ignition switch the lock cylinder might be stuck. You can either contact locksmiths or insert the key into the ignition switch, then move it to the ACC to release the lock cylinder's pin.

A locksmith will be able to use a shear cylinder removal tool or cut the pin off of the lock cylinder with torch and then shave it to remove it from the assembly. They will be able to re-key the cylinder to match the keys you have and save you the cost of a new ignition cylinder.

Replacing the Ignition Cylinder

The ignition Cylinder is a cylindrical mechanical part that houses and secures the key to your car. The cylinder "reads" the anti-theft codes and matches your key to allow you to start or stop your car. As time passes the cylinder wears out. It may also become bent or broken. In this situation, you will need to replace the cylinder to get your car ignition locked started.

A worn or broken cylinder can cause problems turning the key, or the ignition switch will not move into the ACC position or RUN or a warning light to appear on the dashboard. If you have a spare, consider using it in the lock. You may be able to smooth the cylinder using graphite or WD-40, however this method is only effective for so long.

Replace the ignition cylinder if you have a replacement key. Follow the steps above to install the new ignition cylinder. When installing the new ignition cylinder, ensure that it is installed in the steering column tube flange and is correctly aligned with the keyway on the steering column shroud. Check the manual of your car or an expert to confirm that the cylinder is aligned correctly.

Once the cylinder is installed and the key is turned to the ACC or RUN position. Watch for a click which indicates that the ignition switch is fully set in the cylinder. If your vehicle is equipped with an anti-theft system, you will need to perform the anti-theft relearning procedure for the new ignition cylinder in order to program it to your key.

Some experts recommend that you hire a professional to replace the cylinder in your ignition. This is due to the fact that it's usually necessary to deactivate the airbag in the steering column for access to the cylinder. The replacement may require removing the steering wheel and the ignition covers. This is why you should let a mechanic with experience. They'll be able to take off the cover for the steering column and properly install a new ignition lock cylinder in your vehicle. They'll also make sure that the ignition lock cylinder has been programmed with your key and begins to work properly when you insert it.

Installing the Ignition Cylinder

Even though cylinders for ignition locks have been less significant in modern vehicles due to remote start and push-tostart systems older cars still use them. If you're having trouble getting your car started or the ignition switch is faulty, it could be an issue with your ignition cylinder. Luckily, it's relatively easy to replace your vehicle's ignition lock cylinder and repair the problem.

The ignition cylinder is a mechanical part of the system which connects to the ignition switch of your car and provides power to the rest the engine. The ignition switch and the ignition cylinder are two separate components. The switch is an electrical component that connects to your car's computer system to send signals to start the engine when you turn the ignition key.

Ignition lock cylinders feature pins that move up and down to allow your key to slide into and rotate inside the cylinder. Each movement of the cylinder and the key creates a tiny friction that helps keep the key in place but over time, these tiny movements can cause the tumblers on the wafer to wear down. When the tumblers are worn down, the key of your car won't be able to slide into or turn the cylinder.

A damaged ignition cylinder is typically the first sign of trouble in the majority of vehicles. The key could also become stuck and difficult to insert into or out of the ignition lock cylinder. These are all signs that the ignition lock cylinder needs to be replaced as soon as possible.

It's easy to replace the ignition cylinder, but you should only do it if are certain that you will follow the correct procedure for your specific model and make. You can complete the task quickly and correctly by using a complete repair ignition lock Cylinder manual for your vehicle. If you're not comfortable installing the ignition cylinder on your own make one of our ASE certified mobile mechanics perform the repair for you at a time and place that's convenient for you.

Test the Ignition Cylinder

The ignition lock cylinder, also referred to as the ignition lock cylinder, is a mechanical part that fits on your key to allow it to turn and start your vehicle. It is placed inside the ignition switch that locks the ignition, and reads the anti-theft code to authorize key turning. The cylinder for the ignition lock is susceptible to wear and can eventually fail, causing issues powering your vehicle or making it difficult to insert and remove the key.

Some of the most common signs that your car's lock-cylinder is about to fail is difficulty in starting it, or places where the key is caught when you turn it. These problems are usually a sign that the cylinder needs to be replaced. You might even see a warning light flashing on your dashboard to signal the possibility of a failure.

As the cylinder gets older, it may be damaged due to wear and wear and tear. This can cause the pins and wafer tumblers to wear down and break and prevent the ignition of your car from unlocking. The ignition might still work in some cases when you move it around. However, this could be a sign that something is not right.

You can examine the cylinder in your ignition and see whether the cylinder or key is damaged or worn out. You can test with a multimeter whether there's a voltage connection between the red wire connection of the module and the battery terminal of the ignition coil. If you do not find any voltage, the module and switch will most likely require replacement.

Replacing the ignition cylinder typically costs between $200 and $300, and it's usually best to have a professional mechanic perform the task. It's not an easy task because you may have remove other components, such as the steering column to reach the ignition cylinder. The replacement process may require you to turn off the airbag system and reprogramme your key to work with the new ignition cylinder. This is typically done at the dealership, but you can learn how to do it yourself with the proper tools and instructions.