• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Repairing a broken door hinge is a simple task for the majority of homeowners. If the screw holes are shattered and do not hold screws, you may require dowels and wood glue in order to reinstall the door hinge.

Before you do that, however you should clean off any surface corrosion. This will allow the dowels to remain in place and provide them a solid foundation to rest on.

Removing the Hinges

A lot of door hinges are removable, which makes it easier to move the door from one side to the next or to remove the entire door off of the frame if need be. Removing the hinges is fairly easy for anyone with patience, although you need to know how to do it correctly.

If the hinges have been painted you'll need to take off it before you attempt to remove the pins. You may scratch your door if you do not remove the paint. Place the hinges in a stainless steel pot and fill it with water to the point that the hinges are submerged. Let the hinges sit in the pan for around 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

After the pins have been loosen then you can remove the hinges from the frame and door. You can make use of a screwdriver to get the job done, but it is recommended that you employ a magnetic screwdriver to complete this project. This type of screwdriver was designed to pick up screws made of metal and can make the work speed up.

Before you attempt to remove the hinges, it is recommended to spray them with a oil. A simple lubricant will help you accelerate the process and make the removal of screws and pins easier. This kind of lubricant is able to be found in a variety of hardware stores as well as home improvement shops.

The number of hinges you need will also vary depending on the kind of door you have, and how it's installed. Doors with a heavier core and solid-core will require more hinges, while lighter-weight and hollow-core doors might only require two or three hinges.

Understanding the various types of hinges will help determine which one is best for your situation. Exterior hinges are designed to support the weight of a door, while interior hinges need to be able to support heavier loads.

Reattaching the Hinges

Sometimes a door hinge will become looser over time and begin to hang out of alignment or slide. This can cause problems, but it's usually easy to repair. A simple retightening will usually resolve the issue. If the screw holes have been stripped out, it may be difficult to do. A dowel made of wood can be used to tighten the holes once more.

Begin by drilling the hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a secure fit, the dowel should be cut at the same length as the screw. Then, reinstall the screw and tighten it to the desired degree of tightness. If the upvc door hinge replacement does not stop bind up, you can insert another dowel to the gap. Repeat the procedure. Make sure to close the door slowly in order to verify the clearances at the perimeter after each adjustment.

You can also use a wooden plug instead of the dowel. This will work equally well, but may take a bit longer to put in. You can tap in the wood piece that has been whittled down to the proper size. If you don't own a woodworking instrument, you can use toothpicks or matchsticks made from wood.

Make use of a countersink to make the hole smaller than the head of screw after you have put it back in place. This will prevent the screw from rubbing against the edge of the doors when they are closed and opened. This will make it easier to tighten the screw after you are reinstalling the hinge.

After reinstalling the hinge, make sure to lubricate the hinge using a dry lubricant. This will prevent it from becoming stuck in the future. Products like PB Blaster or Liquid Wrench are good alternatives. Apply a thin layer of it and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you can make a few repairs. Verify that the screws that hold the hinge plate to both the door frame and the frame are in good condition. If they are loose, tighten them using a power drill or screwdriver. Be careful not to tighten your screws so much that they start to create gaps in the trim joints, or even worse remove the threads.

If you're experiencing issues because the hinge plates are separating from the jamb and door, you can reattach the hinges by applying wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will provide a solid base for the screws and help keep the plates from moving when you drive them into position. Allow the glue to dry before reattaching your hinge.

Another reason for hinges that are loose is that screws are worn out or are missing. You can fix door hinge this problem by replacing the screws with larger ones. Be sure to use a drill bit that is compatible with the size of the screw hole to avoid drilling into other parts of the hinge or jamb.

After you've reattached your hinge close the door and look at the gap between the door and the frame. It should be about the thickness of one nickel all around or less if there's a gap created by a door that was not properly hung. If the hinges were installed correctly, this should not be a problem.

If you find that the hinges remain loose, you can try adding a thicker hinge shim between the hinge plate and the mounting surface, to create a little extra space. You could also try removing the hinge pin from the problem hinge and then pounding it using a hammer to make it more secure or using a new hinge pin altogether. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and keep them in place. Regularly lubricating your hinges will help keep them from becoming stiff or squeaky and will also prolong their lifespan.

Cleaning the Hinges

The friction hinges uk generated by the constant movement of a hinge attracts dust particles. Without periodic cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and accumulate over time. In the end the hinge can become stiff and creaky, and its appearance can deteriorate rapidly. Regular cleaning, lubrication and inspection will preserve the integrity and functionality of hinges on doors.

Check the hinges for corrosion. If the rust has corroded to the point of destroying the surface of the barrel or screw holes, you'll need to replace the hinges. If you can save the hinges, you should first clean away loose rust using steel wool and wire brushes. Apply a commercial rust-removing solution or a homemade solution such as lemon juice on the hinge. Let the rust-removing solution sit on the hinges for a few minutes to penetrate and dissolve any remaining rust.

The tightening of screws can restore hinge function in the event that you don't want to spend money or time to replace hinges. If you've stripped the screws, however, it may be necessary to add an wooden dowel or shim to the hinge. Wooden dowels are round pieces of wood in the form of rods which are available in different lengths and sizes. They can be purchased on the internet, at stores selling woodworking supplies and home improvement centers.

You can also create an shim using metal or plastic depending on the type hinge you are using. To make a dowel, you need to cut a wooden dowel to the desired length. Then, dip a dowel into carpenter's adhesive and insert it in the hole. The glue will hold the dowel firmly in place.

Before cleaning the hinges put down a cloth or towel to shield your flooring from spills. After you have protected the area, clean the casement windows hinges using an easy sponge or cloth coated with a mild cleaner to remove dirt and grime. You can also remove tarnish, dirt, and grime. You can use a toothbrush or small brush to reach hard-to-reach spots in crevices or tight areas.